How to solve GM MDI Interface not connecting errors?

Here are all solutions aimed to help fix GM MDI multiple diagnostic interface connection/communication issues (connection by usb, wireless ethernet, wired ethernet)… big thanks to all contributors and obdii365.com

For mdi not connecting…

First, you should make sure that the MDI Manager software should be installed on the PC and the MDI must be powered up before you use it to communicate.

Also the MDI should be configured for wired ethernet or wireless communication. If the USB is available, the MDI will connect by using the USB and if not, the MDI will connect by using wired ethernet and if neither of them is available, the MDI will connect by using wireless.

If the MDI can not communicate with the MDI, you should check the cables if they are securely attached to the MDI, if the MDI has completed its power up sequence, if the connector pins are clean and if the MDI Manager software is running.

In detail…. mdi connection can be discussed in the following 4 parts:

Part 1: GM MDI USB connection

Part 2: GM MDI connection by wireless ethernet

Part 3: GM MDI connection by wired ethernet

Part 4: Tech support: GM MDI not connecting

Part 1: GM MDI USB connection

And if you connect them by USB, you need to check the MDI USB connection is detected by windows. About the solutions, you can connect the MDI to the PC USB port and power up the MDI. Open the Network and Dial-up Connections Window from the Windows Control Panel. Then check for the device name ETAS USB Remote NDIS Network Device. If it is not running, check all USB ports on the PC and verify that the MDI is powered on.

GM MDI Manual: What if MDI fails to connect on USB

interface?

Check USB cable connections.

Check Firewall Settings on your PC.

Verify a USB Hub is not being used (MDI has a fixed USB address).

Verify that only one MDI is connected to your PC using USB.

Verify the USB driver has been installed on the PC (look for device name ‘ETAS USB Remote

NDIS Network Device’ under Network Connections).

Try connecting to other USB ports on the PC.

Part 2: GM MDI connection by wireless ethernet

If you connect them by wireless ethernet, you should make sure that wireless communication is enabled and the IP configuration is properly set using the MDI Manager software. Then what you need to check is that the USB cable is not plugged in, the MDI is not being used via wired ethernet and the wireless card is properly seated in the MDI. You can contact your IT department and check that your PC is detecting the wireless access point and the correct security settings have been configured for the MDI.

GM MDI Manual: What if MDI fails to connect on Wireless

interface?

Check the wireless card is properly seated in the WiFi GM MDI.

Confirm LEDs on the wireless card are lighted when the MDI is powered.

Verify the MDI and PC are within range of the Access Point or Router.

Verify that the PC is connected to the Access Point or Router.

Verify signal strength of the wireless network from the PC.

Check Firewall Settings on your PC

USB connection takes precedence, unplug USB cable.

Wired Ethernet connection takes precedence, unplug Ethernet cable.

Connect to MDI using USB and run MDI Manager to verify the Wireless Settings are

configured correctly.

o Wireless interface is enabled.

o AP settings configured for proper security (authentication, encryption).

o Signal Quality (fair, good, excellent) indicates connected to AP.

o The MDI, PC and AP are on the same subnet

o If using static IP, verify the IP Address and Subnet mask are correct (supplied by network

administrator.

Part 3: GM MDI connection by wired ethernet

And if you connect then by wired ethernet, you need to ensure that the wired ethernet communication is enabled and configured using the MDI Manager software. Then you should check that the USB cable is not plugged in and the MDI device detects wired ethernet activity by viewing the lights blinking on the wired ethernet port of the MDI. And also you can contact your local IT department and check that the MDI and the PC are on the same subnet.

GM MDI Manual: What if MDI fails to connect on Wired

Ethernet?

Check Ethernet cable connections.

Check Firewall Settings on your PC.

Verify the MDI and the PC are cabled into separate LAN connections on the same network.

Verify that the PC is properly configured and can communicate on the network.

USB connection takes precedence, unplug USB cable.

Connect to MDI using USB and run MDI Manager to verify the Wired Ethernet Settings are

configured correctly.

o Wired Ethernet interface is enabled.

o If using static IP, verify the IP Address and Subnet mask are correct (supplied by your

network administrator).

Part 4: GM MDI not connecting

This is professional technical support for the error ” not connected to MDI”.

All what you need do is to refresh the GM MDI firmware

1. Press this button and connect the power:

2. Keep press this button and connect it to power, the power light will be on, wait about 10 seconds:

3. When all light is on, then you can release the button, and it will enter firmware refresh status:

4. Connect GM MDI with your PC via USB cable, prepare to refresh the firmware:

5. Open “GM MDI Manager”, choose “Recover”:

Tech support from http://www.obdii365.com/

http://www.obdii365.com/service/gm-mdi-not-connecting-how-to-solve-107172.html

Free Download GM MDI GDS2 v19.0.04100 Software

Free download GDS2 v19.0.04100 version with GDS2Java v14.0.00000 copied from original GM MDI software installation:
https://mega.nz/#!tCZV3aSa!tKHq4JIDlL3kgLgmPeL2WIL8xO7W2qWhrPu0mCo1GxU

If you want download Deliverable GM Global & Opel-Vauxhall 2017.11 packages you can see this link:

https://cartechnology.co.uk/showthread.php?tid=31168

How To install?
How To use deliverable packages?

3. install GDS2Install then install GDS2JavaInstall
   4. Put the zip file called deliverable_OpelVauxhall v2017.5.0 into the below folder:
   C:\ProgramData\GDS 2\PersistentData\Downloads\DataBackups
   5. Open GDS2 and click ManageDiagnostics Packages
   6. click on browes
   7.then go to C:\ProgramData\GDS 2\PersistentData\Downloads\DataBackups
   8.then click on deliverable_OpelVauxhall v2017.11.0 click on open
   9 gds2 will restart

Test successfully?

Good job here see the photo …. the only problem I have with that is javom- problem with MDI interfae when I install the version of MDI -8.3.103.117 after the restart VmWare application that passthru MDI is not ready. When connecting Bosch Kts Pasthru then is ok, Abritus Audio Passthru and that’s ok. MDI-Passthru is not ok not see it.

Note: this be installed with global tis v32 but gds2 packed 2011 year establishes

For tech2win you can try with an other emulator.exe found on this forum cartechnology.co.uk.
Because emulator tech2win on this vmware don’t propose To choose interface.

If you want to use GDS2 on GM MDI with relief, you’d better get a tested version:

Src: http://www.obdii365.com/wholesale/gm-mdi-gds2-gm-mdi-gds-tech-2-win-software.html

It’s confirmed to work with MDI interface without any issue!

http://blog.obdii365.com/2018/12/25/download-gds2-v19-0-04100-for-gm-mdi/

SPS Programming: J2534, VXDIAG or GM MDI?

I buy online SPS programming, connect via j2534. VIN reading OK, but when I try program no matter which module I have E4399 error.

Abrites j2534 won’t work with SPS GDS2 and car from 2014 I think. I need to buy MDI multiple diagnostic interface or something else?

Just information for you to make a wise purchase of GM scan tools for SPS programming: (here, I focus on SPS GDS2 on Abrites j2534 and GM MDI)

In the past ( few years ago when I bought my AVDI )

When I bought my tool I used Global Tis v32 and was able to do SPS Programming in my Y20DTH that I have at my desk for tests. All went OK.

After a while during a year of AMS I received the new drivers but because I didn’t like how the AVDI is working and because I make some money using it I dece to upgrade to genuine OEM tool for the brands that AVDI can work.

After a while I bought a genuine MDI.

And after years I did the tests because my friend who has a issue doing SPS Programming. And he asked me to check if its ok at me. And using same ecu that I did SPS Programming alright in the past then now was blocked. So I did and had the same issues as him.

He because has the AMS he received the new drivers after he talked with Abrites company.
For me AVDI its did it job long time ago and I don’t need to buy a new AMS. So I am using when I do what “she” can do.

My friend asked Abrites to fix this issue and they sent to him new drivers versions and then he could do a SPS Programming as well.

But take care this is not working in any ecu.

So my advise for you is to buy a good GM MDI but not VXDIAG VCX Nano and you will be fine.

In my opinion for GM cars and if you wanna do SPS Programming and diagnostics using Tech2win and GDS2 the better is a GM MDI – a genuine or good clone one, or a cheaper cable like a genuine or good clone Mongoose GM Pro2

Or a J2534 tool that its approved by GM.

Maybe for diagnostic AVDI is still good but for programming it will not for sure. But if you wish it you can use it and when you will block first ecu you will remember my opinion.

AVDI I hadn’t used anymore for diagnostic so I cannot tell you if its ok to use it in newer car with GDS2. Actually I have no new drivers for a long.

I just want to show you my experience and tell you my opinion. The decision is yours.

The last, two very important charts for you – might help your purchase

Tool / Software	GDS2	Tech2Win	Global TIS	TIS2000
GM Tech 2	No	Yes (for old cars)	No	Yes
GM MDI	Yes (for new cars 2010-)	Yes (for old cars)	Yes	No
Mangoose PRO GM II	Yes (for new cars 2010-)	Yes (for old cars)	No	No
VXDIAG VCX Nano GM	Yes (for new cars 2010-)	Yes (for old cars)	No	No

Functions/ Software	GDS2	Tech2Win	Global TIS	TIS2000
Diagnostics	Yes	Yes	No	Yes
ECU Programming	No. But you can log in www.acdelcotds.comto do programming	No. But you can log in www.acdelcotds.comto do programming	Yes. But only program ECUs offline for part of GM vehicles.	Yes
Key Programming	Yes. But you have to program new keys online via www.acdelcotds.com	Yes. But you have to program new keys online via www.acdelcotds.com	No	Yes
SPS Programming	No	Yes	Yes	Yes (with Tech 2 Go-between)

That is,

If you want to do ECU programming or SPS programming, you’d better have a GM MDI interface with Global TIS.

If you need program new keys (only online with GDS2 and Tech2win), it depends.

If you have a new car or pickup truck after the year 2010, you have 3 options: MDI interface, Mangoose cable, Nano;

If you have an old car or pickup truck, you have one more option, Tech 2. That is, 4 options for the old GM vehicles: MDI, Mangoose, Nano and Tech 2.

If you want to have a diagnostic test on GM vehicles, you can have any tool with GDS2 or Tech2win or TIS2000. Clearly, all tools above can be used for GM diagnosis.

Good luck

http://blog.obdii365.com/2018/12/20/sps-programming-abrites-avdi-or-gm-mdi/